Arkray SPOTCHEM EZ SP-4430, Operating Manual

Page: 126 / 139

C SP-4430 ● 5-09
4-1
お手入れの概要
Chapter 5 TROUBLESHOOTING
4-1-1 お手入れの目安
Failure to discard tip.
●
Turn off the power, and remove the
tip from the nozzle.
●
T21
Ｔ２１ Ｔｉｐ ｅｊｅｃｔｉｎｇ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
White plate or black plate is dirty.
●
Clean the white plate or black plate.
(Note: the case in which trouble is
detected when the power is turned
on, it is necessary to turn on the
power again after maintenance
since measurement cannot be
started).
●
T25
Ｔ２５ Ｂａｒｃｏｄｅ ｓｅｎｓｏｒ
（ ■ ８ ■■ ５ ■ ３ ■■ ） ■ ＯＫ（ＥＮＴＥＲ）
(1- 5, 7- 9 ) :Channels with abnormalities
The rotating rate of centrifuge is
defective.
It cannot rotate due to an obstruction
around the centrifuge.
Forgot to set centrifuge tube.
Protective cover is not properly
attached.
●
●
●
●
Remove the obstruction around the
centrifuge.
Turn on the power again.
If the same trouble occurs, contact
your distributor.
Set the centrifuge tube.
Attach the protective cover properly.
●
●
●
●
●
T27
Ｔ２７ Ｃｅｎｔｒｉｆｕｇｅ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Trouble occurred in the centrifuge front-
back driving mechanism.
It cannot operate because of an
obstruction in the operating path of the
centrifuge base.
●
●
Turn on the power again.
Confirm that there is no obstruction.
If the same trouble occurs, contact
your distributor.
●
●
●
T28
Ｔ２８ Ｃｅｎｔｒｉｆｕｇｅ Ｆ／Ｂ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Trouble with product information
memory storage.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs, contact
your distributor.
●
T90
Ｔ９０ Ｍｅｍｏｒｙ：ｐｒｏｄｕｃｔ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Description and trouble message Conditions and causes Remedy
Trouble with mechanism information
memory storage.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs, contact
your distributor.
●
T91
Ｔ９１ Ｍｅｍｏｒｙ：ｍｅｃｈａｎｉｓｍ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Trouble with optical system information
memory storage.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs, contact
your distributor.
●
T92
Ｔ９２ Ｍｅｍｏｒｙ：ｏｐｔｉｃａｌ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
(Cover) :Protective cover is not attached
(Position) :Stop position is not correct