C
SP-4430 ● 2-33
2-5
校正
Chapter 2 MEASUREMENT
2-5-1
校正の概要
To stop calibration, press
[STOP] key.
▲
There is no order for inserting the
stripes. Any stripe can be inserted
first.
▲
Insert calibration card.
4.
Press [2] key on the CALIBRATION
MENU.
The Magnetic card entry screen is
displayed.
Insert the stripe of a calibration card
in the magnetic card reader and
slide the card to the right.
When the stripe is inserted, the
message shown on the right is
displayed.
Insert the same stripe again
according to the message on the
screen.
When the same stripes are inserted
twice, that stripe number is
displayed on the lower part of the
screen. The entered stripes are
displayed as
■
.
Insert the rest stripes twice
according to the message on the
screen. When all stripes are
inserted, lot number of the calibrator
is displayed.
After that, the Calibration standby
screen is displayed.
The Table Cover opens, and the
Reagent Table and the Centrifuge-
equipped Multi Rack slide forward.
The Calibration standby screen as
shown on the right is displayed.
●
●
●
●
●
●
●
Insert the same stripes twice to
surely read the stored information
in the calibration cards.
There is only one stripe for Hb,
this screen is not displayed.
▲
If no key entry is made within 3
minutes after the Table Cover
opens, an alarm sounds and
the Table Cover closes.
If press [STOP] key is pressed
while
“
CANCEL
”
is displayed,
the Standby screen is restored
without closing the Table
Cover.
After the Table Cover closes,
the message shown on the
right is displayed.
To go back to the MAIN MENU,
press [STOP] key.
To go back to the Standby
screen, press [ENTER] key.
▲▲
▲
I n s e a r t
a c a r d .
T h e s a m e s t r i p e .
I n s e a r t
a c a r d . C a l .
A n o t h e r
s t r i p e ■234
S t a n d b y
L
=0
H=0
N=?
I n s e a r t
a c a r d . C a l .
【 C A LーC A R D
】【 X X X X X X 】
C o v e r
i s c l o s i n g .
S t o p( S T O P )
I n s e r t
a c a r d .
T h e s a m e s t r i p e
B a c k
t o M E N U( S T O P )
B a c k
t o C A L ( E N T E R )
Summary of Contents for SPOTCHEM EZ SP-4430
