Arkray SPOTCHEM EZ SP-4430, Operating Manual

Page: 123 / 139

C 5-06 ● SP-4430
4-2
毎日のお手入れ
Chapter 5 TROUBLESHOOTING
4-2-2 チップ廃却ケースの清掃
Description and error message Conditions and causes Remedy
The memory storing the measured
results is defective.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs often,
contact your distributor.
●
E90
Ｅ９０ Ｍｅｍｏｒｙ：ｒｅｓｕｌｔｓ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
The memory storing the trouble history
is detective.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs often,
contact your distributor.
●
E91
Ｅ９１ Ｍｅｍｏｒｙ：ｈｉｓｔｏｒｙ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
The memory storing the setup data is
defective.
Power was cut while writing in memory
or deleting.
●
●
If the same trouble occurs often,
contact your distributor.
As the user setting value is
initialized or is returned to the last
measured value, reset it (re-enter
it).
●
●
E92
Ｅ９２ Ｍｅｍｏｒｙ：ｓｅｔｕｐ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
The cable is not connected.
The setting (e.g. baud rate) of the
connected device (such as PC) is
incorrect.
●
●
Connect the cable correctly.
Confirm the setting (e.g. baud rate)
of analyzer connections (e.g. PC).
●
●
E39
Ｅ３９ Ｃｏｍｍｕｎｉｃａｔｉｏｎ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Forgot to set the Tip Waste Case.
The Tip Waste Case is not correctly set.
●
●
Set the Tip Waste Case correctly.
●
E38
Ｅ３８ Ｔｉｐ ｃａｓｅ ｎｏｔ ｓｅｔ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
When sampling, air bubbles or fibrin
was aspirated.
When sampling, the sample amount
was insufficient.
●
●
Remove air bubbles or fibrin.
Confirm the sample amount.
●
●
E37
Ｅ３７ Ｓａｍｐｌｉｎｇ ｅｒｒｏｒ
■■■■■■■■■■■■ ＯＫ（ＥＮＴＥＲ）
Wear protective gloves in order to avoid exposure
to pathogenic microbes.
WARNING
Failed to draw the sample and drop it to
the reagent correctly due to lack of
sample amount or absorbing fibrin.
Failed to drop the sample to the reagent
correctly because the sample adheres
around the dropping hole.
●
●
Check the sample amount and
remove fibrin if necessary.
Wipe off the sample adhered to
around the dropping hole.
Measure it with a different tip.
●
●
●
E40
Ｅ４０ Ｓａｍｐｌｅ ｄｒｏｐ
（ ■■ 7 ■■ 4 ■■ 1） ■■■ ＯＫ（ＥＮＴＥＲ）
（１〜９）：Channels with abnormalities