Arkray SPOTCHEM EZ SP-4430 Page 107 Operating Manual Download

Page: 107 / 139

SP-4430 ● 4-09

4-1

お手入れの概要

Chapter 4 MAINTENANCE

4-1-1

お手入れの目安

Prepare new printer paper.

Cut off a single turn of the paper of

new roll. Cut the top end straight to

avoid a paper jam.

●

Set new printer paper.

Place a new roll of paper in the

paper holder, with the paper end

facing up.

Insert the top of the paper end into

the slot. The paper starts to be

rolled and fed automatically.

Press [FEED] key once.

The printer becomes ready for

printing.

●

Close the printer cover.

Close the printer cover until it clicks

into place.

●

NOTE

Be careful not to touch the paper

cutter to avoid injury.

To make the printer ready for

printing, press [FEED] key.

▲

Summary of Contents for SPOTCHEM EZ SP-4430












































































































































Search results

Summary of Contents for SPOTCHEM EZ SP-4430

Reviews:

Related manuals for SPOTCHEM EZ SP-4430

Brands by name

Popular brands

Arkray SPOTCHEM EZ SP-4430, Operating Manual

Search results

Summary of Contents for SPOTCHEM EZ SP-4430

Reviews:

Related manuals for SPOTCHEM EZ SP-4430

Brands by name

Popular brands