Applied Biosystems 2720 User Manual Download Page 81

Page: 81 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 6

Temperature non-uniformity test

10. When you complete all measurements, be sure to:

• Press

(Cancel).

• Remove the 20-µL probe assembly from the sample blocks.

• Power off the digital thermometer, then clean off the oil.

• Remove the 384-well temperature verification plates from the sample

blocks.

IMPORTANT!

Make sure the sample blocks are at room temperature (~25 °C)

before removing the reaction plates.

Evaluating the

results

When the GeneAmp

9700 completes the temperature non-uniformity test, the TNU

Performance screen opens. See the table below to evaluate the results.

If the...

Then...

Temperature of the
sample block wells is
uniform

“Pass” appears after each setpoint temperature.

Temperature variation of
the sample block wells
exceeds performance
specifications

“Fail” appears after the setpoint temperature(s) for which the
test failed.

• If the test fails, repeat the procedure to make sure that the

thermometer was not misread or that data-entry errors were
not made.

• If the test fails again, contact Applied Biosystems Technical

Support. See

“How to obtain support” on page viii

TNU Performance

TNU at 94°C is xx.xx - Pass
TNU at 37°C is xx.xx - Pass

Cancel

TNU Performance

TNU at 94°C is xx.xx - Fail
TNU at 37°C is xx.xx - Fail

Cancel

Summary of Contents for 2720
























































































































































Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands

Applied Biosystems 2720, User Manual

Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands