Applied Biosystems 2720 User Manual Download Page 73

Page: 73 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 6

Calibration verification test

3. Use the stick end of a cotton swab to coat well R3 with mineral oil; The wells

are too small for the swab end.

4. Place the 20-µL probe assembly into well R3.

5. Thread the probe wire through the channels in the 384-well temperature

verification plate to prevent damage to the probe and lead wires.

6. Make sure the probe is connected to the digital thermometer.

7. Press and release the red button to automatically close the heated cover.

IMPORTANT!

Seat the probe properly. If the probe wire is crushed when the

heated cover closes, the probe may be damaged

8. Power on the digital thermometer.

Refer to the instructions in your Temperature Verification Kit for details on
operating the digital thermometer, Model 4500.

Configuring the

GeneAmp

9700

1. Power on the thermal cycler. The Main menu opens.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to
ambient temperature before performing the test.

2. Press

(Util).

The Utilities screen opens.

3. Press

(Diag). The Diagnostics screen opens.

4. Press

(TmpVer). The Temperature Verification screen opens.

5. Press

(Temp) to automatically configure the GeneAmp

9700 for the

calibration verification test. The Calibration Verification screen opens.

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

Temp

Exit

TNU

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Place probe in well R3
Press Run

Run

Cancel

Summary of Contents for 2720
























































































































































Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands

Applied Biosystems 2720, User Manual

Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands