Applied Biosystems 2720 User Manual Download Page 46

Page: 46 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 4

Calibration verification test

7. For GeneAmp

9700 with Manual Dual 96-Well Sample Block Module:

Slide the heated cover forward then pull the lever down.

For GeneAmp

9700 with Auto-Lid Dual 96-Well Sample Block Module:

Press the red button to slide and close the heated cover.

IMPORTANT!

Seat the probe properly and close the heated cover carefully. If

the probe wire is crushed when you close the heated cover, the probe can be
damaged.

8. Power on the digital thermometer.

Refer to the instructions in your Temperature Verification Kit for details on
operating the digital thermometer, Model 4500.

Configuring the

GeneAmp

9700

1. Power on the thermal cycler. The Main menu opens.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to
ambient temperature before performing the test.

2. Press

(Util).

The Utilities screen opens.

3. Press

(Diag). The Diagnostics screen opens.

4. Press

(TmpVer). The Temperature Verification screen opens.

5. Press

(Temp).

The GeneAmp

9700 is automatically configured for the calibration

verification test, and the Calibration Verification screen opens.

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

Temp

Exit

TNU

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Place probe in well R3
Press Run

Run

Cancel

Summary of Contents for 2720
























































































































































Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands

Applied Biosystems 2720, User Manual

Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands