manualshive.com logo in svg

Applied Biosystems 2720, User Manual

Share
Download
Applied Biosystems 2720 User Manual Download Page 20

12

Thermal Cycler Temperature Verification System For GeneAmp

® 

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

®

 System User Guide

Chapter 2

Temperature calibration verification test

Evaluating the

results

When the thermal cycler completes the calibration verification test, one of two 
screens opens, depending on the results. See the table below to evaluate the results.

Note:

As a result of the Temperature Tolerance Stack, between the sample block, 

temperature probe and thermometer, the instrument firmware is programmed to 
accept a Pass/Fail result of ±0.75 °C. Therefore, passing results may vary from 
84.25 °C to 85.75 °C at the 85-degree setpoint and 44.25 °C and 45.75 °C at the 45-
degree setpoint. Ranges greater than 

±

 0.75 degrees cause the test to fail.

Ending the test

1. Press 

F5

 (Exit).

2. Remove the 0.2-mL probe assembly from the sample block.

3. Power off the digital thermometer, then clean off the oil.

Wait for the sample block to reach room temperature (~25 °C), then remove the 
2720 temperature verification frame from the sample block.

PHYSICAL INJURY HAZARD.

 Hot Surface. Use care 

when working around the heated cover and sample block to avoid being burned 
by hot components.

4. Clean the oil off the sample block.

If the sample block 

module...

Then the...

Is properly calibrated

Calibration Verification screen displays the following message:

Does not pass the 
calibration verification 
test

Calibration Verification screen displays the following message:

• If the test fails, repeat the procedure to make sure that the 

thermometer was not misread or that data-entry errors were 
not made.

• If the test fails again, contact Applied Biosystems Technical 

Support. See 

“How to obtain support” on page viii

.

Calibration Verification

Calibration is good

F1

F3

F4

F5

F2

Exit

Calibration Verification

Instrument may require service.

 

Contact Applied Biosystems

F1

F3

F4

F5

F2

Exit

Technical Support.

Summary of Contents for 2720
























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands