Applied Biosystems 2720 User Manual Download Page 18

Page: 18 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 2

Temperature calibration verification test

3. Press

(Diag). The Diagnostics screen opens.

4. Press

(TmpVer). The Temperature Verification screen opens.

5. Press

(Temp). The thermal cycler is automatically configured for the

calibration verification test and the Calibration Verification screen opens.

Running the test

In this test, you take temperature readings of the sample well at two different setpoint
temperatures using the 0.2-mL probe assembly.

Note:

Press

(Cancel) if you want to end the test.

To run the calibration verification test:

1. Press

(Run) to start the calibration verification test. The Calibration

Verification screen opens with the setpoint value displayed.

Note:

The cover must be at 85 °C

10 °C. It may take several minutes for the

system to ramp up.

Note:

The Calibration Verification screen counts down the time until the

setpoint is reached.

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

Temp

Exit

TNU

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Place probe in well A6
Press Run

Run

Cancel

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Setpoint is 85°C
Cover must be within 10°C of 85°C

Cancel

Calibration Verification

Block temp = xx.x°C Cover temp = xxx°C

Stabilizing at setpoint

x:xx

Cancel

Summary of Contents for 2720
























































































































































Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands

Applied Biosystems 2720, User Manual

Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands