Applied Biosystems 2720 User Manual Download Page 106

Page: 106 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 8

Temperature non-uniformity test

Configuring the

GeneAmp

9800

1. Complete the procedures in

“Setting up the 0.1-mL probe assembly” on

page 97

2. Power on the GeneAmp

9800.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to
ambient temperature before performing the test.

3. In the main menu, press

(Util)

to open the Utilities screen.

4. Press

(Diag) to open the Diagnostics screen.

5. Press

(TmpVer) to open the Temperature Verification screen.

6. Press

(TNU) to open the TNU Performance screen and configure the 9800

for the temperature non-uniformity test.

Note:

If the cover temperature is not within

1 °C of the heated cover setpoint,

the following screen opens:

7. Continue with

“Running the test” on page 99

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

Temp

Exit

TNU

TNU Performance

Sample temp = xx.x°C Cover temp = xxx°C

Place Probe in well A1
Press Run

Run

Cancel

TNU Performance

Sample temp = xx.x°C Cover temp = xxx°C

Cover setpoint is 55C
Cover must be within 1.0C of setpoint

Cancel

Summary of Contents for 2720
























































































































































Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands

Applied Biosystems 2720, User Manual

Search results

Summary of Contents for 2720

Reviews:

Brands by name

Popular brands