manualshive.com logo in svg

Abarth Punto, Owner'S Handbook Manual

The Abarth Punto Owner's Handbook Manual is the comprehensive guide you need to get the most out of your vehicle. This manual, available for free download at manualshive.com, provides detailed instructions, maintenance tips, and essential information to ensure optimal performance. Unlock the full potential of your Abarth Punto today!

Share
Download
background image

191

KNOWING

YOUR VEHICLE

SAFETY

STARTING 

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN 

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

F0U174Ab

fig. 170

IMPORTANT Brake fluid absorbs moisture. For this
reason, if the vehicle is mainly used in areas with a high
degree of atmospheric humidity, the fluid should be
replaced at more frequent intervals than specified in the
“Scheduled servicing plan”.

BRAKE FLUID fig. 170

Undo the cap A and check that the liquid contained in
the reservoir is at the maximum level.

Fluid level in the reservoir must not exceed the MAX
mark.

Use the brake fluid shown in the “Fluids and lubricants”
table (see “Technical Specifications”).

Note Carefully clean the cap of the reservoir A and the
surrounding surface.

Take great care that impurities do not enter the
reservoir when the cap is opened.

For topping up always use a funnel with integrated filter
that has a mesh inferior or equal to 0.12 mm. 

Prevent brake fluid which is highly
corrosive from coming into contact with
painted parts. Should this occur,

immediately wash with water. 

Brake fluid is poisonous and highly
corrosive. In the event of accidental

contact, immediately wash the affected parts
with water and neutral soap. Then rinse
thoroughly. If swallowed call a doctor
immediately. 

WARNING

183-204 PUNTO Abarth GB 1ed  17-07-2012  15:17  Pagina 191

Summary of Contents for Punto
















































































































































































































































































Reviews:

No comments

Related manuals for Punto

JAC S5 Workshop Manual preview
S5
Brand: JAC Pages: 70
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Brand: Eaton Pages: 12
Eclipse AVN 2210p mkII Operation Manual preview
AVN 2210p mkII
Brand: Eclipse Pages: 6
Warrior Products 10936 Installation Instructions preview
10936
Brand: Warrior Products Pages: 3
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Brand: Yakima Pages: 8
DAVIS 8126GD User Manual preview
8126GD
Brand: DAVIS Pages: 32
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Brand: Curt Manufacturing Pages: 6
Caltrend CV445 Installation Instructions preview
CV445
Brand: Caltrend Pages: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Brand: Audiovox Pages: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Brand: EGR Pages: 28
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Brand: Volvo Pages: 262
Scion 2012 iQ Quick Reference Manual preview
2012 iQ
Brand: Scion Pages: 24
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416

Brands by name

Popular brands

Load more brands