Abarth Punto Owner'S Handbook Manual Download Page 110 | Manualshive

Page: 110 / 271

background image

106

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

INSTALLATION OF ELECTRICAL/
ELECTRONIC DEVICES

Electrical and electronic devices installed after buying
the car in the context of after-sales service must carry
the following label:

Fiat Group Automobiles S.p.A. authorises the
installation of transceivers provided that installation is
carried out at a specialised centre, in a workmanlike
fashion and in compliance with manufacturer’s
specifications.

IMPORTANT Traffic police may not allow the car on
the road if devices have been installed which modify the
features of the car. This may also cause invalidation of
warranty in relation to faults caused by the change
either directly or indirectly related to it.

Fiat Group Automobiles S.p.A. shall not be liable for
damage caused by the installation of accessories either
not supplied or recommended by Fiat Group
Automobiles S.p.A. and/or not installed in compliance
with the instructions provided.

TRANSCEIVERS AND MOBILE PHONES

Radio transmitter equipment (vehicle mobile phones,
CB radios, amateur radio etc.) cannot be used inside the
car unless a separate aerial is mounted on the roof.

IMPORTANT The use of these devices inside the
passenger compartment (without a separate aerial) may
cause the vehicle electrical systems to malfunction. This
could compromise safety in addition to constituting a
potential hazard for passengers’ health.

In addition, transmission and reception of these devices
may be affected by the shielding effect of the car body.
As far as the use of EC-approved mobile phones is
concerned (GSM, GPRS, UMTS), follow the usage
instructions provided by the mobile phone
manufacturer.

069-108 PUNTO Abarth GB 1ed 17-07-2012 15:10 Pagina 106

«
...
108
109
110
111
112
...
»

Summary of Contents for Punto
















































































































































































































































































Reviews:

No comments

Related manuals for Punto

Brand: Kuda-Phonebase Pages: 3

Brand: Mazda Pages: 13

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: Rago FABRICATION Pages: 10

Brand: FALCON RIDGE Pages: 8

Brand: Scosche Pages: 8

Brand: Prorack Pages: 15

Brand: Honda Pages: 569

Brand: TrailFX Pages: 2

Brand: Ferve Pages: 28

Brand: Arrista Pages: 2

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Prorack Pages: 14

Brand: Black Horse Off Road Pages: 3

Brand: Dacia Pages: 244

Brand: Whispbar Pages: 15

Brand: Prorack Pages: 14

Brand: Wallbox Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands