Abarth Punto Owner'S Handbook Manual Download Page 108

Page: 108 / 271

104

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

CD CHANGER CAPABILITY

(for versions/markets where provided)

The system consists of:

❒

power cables;

❒

connection cables.

For connection to the preset cables,
contact an Abarth Dealership to prevent

any problem that could impair car safety.

WARNING

When the SHIFT UP icon (

SHIFT) is shown on the

display, the “e-GSI” system is advising the driver to
select a higher gear, while the SHIFT DOWN
(

SHIFT) icon suggests that a lower gear should be

engaged.

Note The “e-GSI” system intervenes only when the
“Normal” driving mode is activated (see the “Manettino
Abarth car dynamic control system (DSS – Driving
Sport Switch)” paragraph in this section).

069-108 PUNTO Abarth GB 1ed 17-07-2012 12:08 Pagina 104

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands