Abarth Punto Owner'S Handbook Manual Download Page 198

Page: 198 / 271

194

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

Batteries contain substances that can be
very dangerous for the environment. It is
advisable to have the battery changed by

an Abarth Dealership, where it will be disposed
of correctly and in accordance with nature and
the law.

If the vehicle must remain unused for a
long time at very low temperatures,

remove the battery and take it to a warm place
to avoid freezing.

WARNING

If you have to perform any operation on
the battery or near it, always protect

your eyes with special goggles.

WARNING

USEFUL ADVICE FOR EXTENDING
THE LIFE OF YOUR BATTERY

To avoid draining your battery and make it last longer,
observe the following instructions:

❒

when you park the car, ensure that the doors,
tailgate and flaps are closed properly, to prevent any
light from switching on inside the passenger’s
compartment;

❒

the courtesy lights must be off. The car is however
provided with an automatic system for switching off
internal lights;

❒

do not keep accessories (e.g. sound system, hazard
warning lights, etc...) switched on for a long time
when the engine is not running;

❒

before performing any operation on the electric
system, disconnect the negative battery cable;

❒

make sure that the battery terminals are fully
tightened.

183-204 PUNTO Abarth GB 1ed 17-07-2012 15:17 Pagina 194

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands