Abarth Punto Owner'S Handbook Manual Download Page 99

Page: 99 / 271

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

In order to use the system properly, refer to the following table when you have to change wheels/tyres:

Operation

Sensor

Failure warning

Abarth Dealership

Service Intervention

–

Replacing a wheel

with the spare wheel

Replacing wheels

with snow tyres

Replacing wheels

with snow tyres

Replacing wheels

with others of

a different size (*)

Switching wheels

(front/rear) (**)

(*) Given as an alternative in the Owner’s Handbook and available at Lineaccessori Abarth.

(**) Not cross-swapped (tyres must stay on the same side).

–

YES

Contact an Abarth

Dealership

Repair the damaged

wheel

Contact an Abarth

Dealership

–

069-108 PUNTO Abarth GB 1ed 17-07-2012 12:08 Pagina 95

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands