Abarth Punto Owner'S Handbook Manual Download Page 183

Page: 183 / 271

179

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

F0U169Ab

fig. 165

FASTENING THE TOW RING
fig. 164-165

Proceed as follows:

❒

release the cap A;

❒

take the tow ring B from its support;

❒

fully tighten the ring on the rear or front threaded
pin.

TOWING THE CAR

The tow ring provided with the car is housed in the tool
box under the carpet in the boot.

fig. 164

F0U168Ab

151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 179

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands