Abarth Punto Owner'S Handbook Manual Download Page 174

Page: 174 / 271

170

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

Never replace a blown fuse with metal
wires or other materials.

Should the fuse blow again, contact an
Abarth Dealership.

WARNING

Never replace a fuse with one that has a
higher amperage: FIRE HAZARD.

WARNING

If a general protection fuse (MEGA-
FUSE, MIDI-FUSE, MAXI-FUSE) blows,

contact an Abarth Dealership.

WARNING

Before replacing a fuse, make sure that
the ignition key has been removed and

that all the other services are switched off
and/or disengaged.

WARNING

If a general protection fuse for safety
systems (air bag system, braking system),

power unit systems (engine system, transmission
system) or steering system blows, contact an
Abarth Dealership.

WARNING

151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 170

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands