manualshive.com logo in svg

Abarth Punto, Owner'S Handbook Manual

The Abarth Punto Owner's Handbook Manual is the comprehensive guide you need to get the most out of your vehicle. This manual, available for free download at manualshive.com, provides detailed instructions, maintenance tips, and essential information to ensure optimal performance. Unlock the full potential of your Abarth Punto today!

Share
Download
background image

102

KNOWING

YOUR VEHICLE

SAFETY

STARTING 

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN 

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

fig. 100

fig. 101

IMPORTANT After turning the ignition key to STOP, wait
at least 1 minute before disconnecting the electrical supply
to the battery.

EMERGENCY STARTING fig. 101

When jump starting, never connect the negative lead (–)
of the auxiliary battery to the negative pole A of the car
battery, but rather to an engine/gearbox earth point.

Note In any case, it is possible to keep the engine
running by deactivating the Start&Stop system. 

IRREGULAR OPERATION

In the case of malfunction the Start&Stop system is
disabled. The driver is informed of the problem by the
general failure warning light 
A-fig. 99, where provided, coming on with an
information message and the system failure symbol 
B-fig. 5 in the control panel. In this case, contact an
Abarth Dealership.

CAR INACTIVITY fig. 100

In the case of car inactivity, special attention must be paid
due to the disconnection of the battery power supply.
Proceed as follows: detach the connector A (by pressing
button B) from sensor C for monitoring the status of the
battery installed on the negative battery pole D. This
sensor should never be disconnected from the pole except
if the battery is replaced.

When replacing the battery, always
contact an Abarth Dealership. Replace

the battery using a new one of the same type
(HEAVY DUTY) and having the same
specifications.

WARNING

069-108 PUNTO Abarth GB 1ed  17-07-2012  12:08  Pagina 102

Summary of Contents for Punto
















































































































































































































































































Reviews:

No comments

Related manuals for Punto

GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Brand: GMC Pages: 20
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Brand: BMW Pages: 160
FORM FIT 1303 Installation Instructions preview
1303
Brand: FORM FIT Pages: 2
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
WABCO TP19108 Installation Manual preview
TP19108
Brand: WABCO Pages: 32
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Brand: Safe Fleet Pages: 12
CALIMA 46008 Operating Instructions Manual preview
46008
Brand: CALIMA Pages: 9
Ranger design 1525-NS Installation Manual preview
1525-NS
Brand: Ranger design Pages: 22
National Cycle Quantum hardcoated N30216 Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30216
Brand: National Cycle Pages: 3
Fortin Evo All THAR-FOR3 Installation Manual preview
Evo All THAR-FOR3
Brand: Fortin Pages: 7
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
GReddy 12519101 Instruction Manual preview
12519101
Brand: GReddy Pages: 12
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Brand: Mont Blanc Pages: 2
Mercedes-Benz Vito Taxi 2011 Operation Manual preview
Vito Taxi 2011
Brand: Mercedes-Benz Pages: 10
Prorack K374 Manual preview
K374
Brand: Prorack Pages: 14
Spracht Aura Mobile BT MCP-2014 Quick Start Manual preview
Aura Mobile BT MCP-2014
Brand: Spracht Pages: 2
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3

Brands by name

Popular brands

Load more brands