Abarth Punto Owner'S Handbook Manual Download Page 61

Page: 61 / 271

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

TIMED OPERATION FOR GETTING OUT OF THE VEHICLE

After removing the key from the ignition, the courtesy
lights switch on according to the following modes:

❒

within 2 minutes from turning the engine off for
about 10 seconds;

❒

when opening one of the side doors for about
3 minutes;

❒

when one of the doors is closed for a period of
about 10 seconds.

The timed delay period ends automatically when the
doors are locked.

F0U041Ab

fig. 41

LUGGAGE COMPARTMENT LIGHT fig. 41

For versions fitted with boot light, the light comes on
automatically when opening the tailgate and it will go
off when closing.

029-068 PUNTO Abarth GB 1ed 17-07-2012 12:06 Pagina 57

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands