Abarth Punto Owner'S Handbook Manual Download Page 37

Page: 37 / 271

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

The head restraints must be adjusted so

that the head, rather than the neck,

rests on them. Only in this case can they
protect your head correctly.

WARNING

REAR fig. 23

To move the head restraint upwards, raise it until a click
is heard (position of use).

To bring it to the position of non-use, press button A
and lower the head restraint into the backrest.

To extract the rear head restraints press buttons A and
B simultaneously and pull them upwards.

IMPORTANT If the rear seats are used, always set the
head restraints in the “completely raised” position.

HEAD RESTRAINTS

FRONT fig. 22

The front head restraints are fixed on the backrest and
cannot be adjusted in height.

To make the best use of the head restraint’s protective
action, adjust the backrest to keep the chest erect, with
the head as close as possible to the restraint.

fig. 22

F0U022Ab

fig. 23

F0U023Ab

029-068 PUNTO Abarth GB 1ed 17-07-2012 12:05 Pagina 33

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands