manualshive.com logo in svg

Abarth Punto, Owner'S Handbook Manual

The Abarth Punto Owner's Handbook Manual is the comprehensive guide you need to get the most out of your vehicle. This manual, available for free download at manualshive.com, provides detailed instructions, maintenance tips, and essential information to ensure optimal performance. Unlock the full potential of your Abarth Punto today!

Share
Download
background image

141

WARNING LIGHTS AND MESSAGES

GENERAL WARNINGS

Switching on of some warning lights/symbols is
associated to a specific message and/or warning buzzer.
These indications are indicative and precautionary and
as such must not be considered as exhaustive and/or
alternative to the information contained in the Owner
Handbook, which you are recommended to read
carefully in all cases. Always refer to the information in
this chapter in the event of a failure indication.

IMPORTANT The fault indicators appearing on the
reconfigurable multifunction display are divided into two
categories: very serious and less serious faults.

Very serious faults prompt a prolonged cycle of signals.

Less serious faults prompt a shorter cycle of signals.

Press MENU ESC to stop the warning cycle in both
cases.

The instrument panel warning lights will stay on until the
causes of the fault are eliminated.

KNOWING

YOUR VEHICLE

SAFETY

STARTING 

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN 

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

WARNING LIGHTS AND MESSAGES

If the warning light 

x

turns on when

travelling (with the message on the

display) stop the car immediately and contact
an Abarth Dealership.

WARNING

BRAKE FLUID 

LOW (red)

HANDBRAKE ENGAGED (red)

When the key is turned to the MAR position the
warning light comes on but should go out after a few
seconds.

Low brake fluid level

The warning light comes on when the level of the brake
fluid in the reservoir falls below the minimum level due
to a possible leak in the circuit.

The display will show a dedicated message.

x

Handbrake on

The warning light turns on when the handbrake is
engaged.

On some versions there is also an associated warning
buzzer if the car is moving.

IMPORTANT If the warning light turns on when
travelling, check that the handbrake is not engaged. 

141-150 PUNTO Abarth GB 1ed  17-07-2012  13:21  Pagina 141

Summary of Contents for Punto
















































































































































































































































































Reviews:

No comments

Related manuals for Punto

Hama Neptun Manual preview
Neptun
Brand: Hama Pages: 6
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
EUFAB 11556 Operating Instructions Manual preview
11556
Brand: EUFAB Pages: 52
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Brand: Omix-Ada Pages: 6
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Brand: ECS Pages: 4
Whispbar WB751 Manual preview
WB751
Brand: Whispbar Pages: 15
Needit Park Mini User Manual preview
Park Mini
Brand: Needit Pages: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Brand: Gemini Pages: 6
Maserati MC 20 2022 Roadside Assistance Manual preview
MC 20 2022
Brand: Maserati Pages: 37
Quadratec QRC Installation Manual preview
QRC
Brand: Quadratec Pages: 8
Axxess AXDSPX-TY3 Installation Instructions Manual preview
AXDSPX-TY3
Brand: Axxess Pages: 16
SportRack EXPLORER A90095 Instruction Sheet preview
EXPLORER A90095
Brand: SportRack Pages: 6
Chevrolet 2002 Silverado 1500 Pickup Owner'S Manual preview
2002 Silverado 1500 Pickup
Brand: Chevrolet Pages: 497
DV8 LBBR-01 Installation Manual preview
LBBR-01
Brand: DV8 Pages: 5
Kia Forte 2023 Quick Start Manual preview
Forte 2023
Brand: Kia Pages: 4
Jeep 2002 WG Grand Cherokee Service Manual preview
2002 WG Grand Cherokee
Brand: Jeep Pages: 10

Brands by name

Popular brands

Load more brands