Abarth Punto Owner'S Handbook Manual Download Page 245

Page: 245 / 271

241

RADIO

PHONE FUNCTION (telephone volume
adjustment) (only with Blue&Me

system)

With Speech volume function present in Menu

This function makes it possible to adjust (settings from 1
to 40), by turning the ON/OFF button/knob or pressing
the

buttons or exclude (OFF setting), the volume

of the Telephone or the

Blue&Me™

(except the Media

Player function).

The display shows the current function status:

❒

“Speech Off”: function deactivated.

❒

“Speech volume 23”: function activated with volume
set to 23.

With Speech volume function not present in Menu

When one phone call is received, the audio passes to the
car sound system through the radio.

The incoming telephone sound is always at a fixed
volume, but it can be adjusted during the conversation
using the ON/OFF button/knob.

If, while using the

Blue&Me™

, the phone call volume is

changed, the same is displayed on the radio display,
memorised and kept for all the following phone calls
until the engine is switched off.

With the RADIO ON VOLUME function activated,
when the engine is started again:

❒

if the radio was switched off with a

Blue&Me™

volume lower than 12, at the next phone call the

Blue&Me™

volume is automatically set to 12;

❒

if the radio was switched off with a

Blue&Me™

volume higher than 25, at the next phone call the

Blue&Me™

volume is automatically set to 25;

❒

if the radio was switched off with a

Blue&Me™

volume ranging between 12 and 25, at the next phone
call the

Blue&Me™

volume is kept as previously set

by the user.

If instead the RADIO ON VOLUME function is
deactivated, the radio keeps the last setting.

SPEECH VOLUME function
(telephone volume adjustment)

This function makes it possible to adjust (settings from 1
to 40), by turning the control fig. 1 or pressing the

buttons or exclude (OFF setting) the volume of the
Telephone, the

Blue&Me™

(except the Media Player

function).

The display shows the current function status:

❒

“Speech Off”: function deactivated.

❒

“Speech volume 23”: function activated with volume
setting 23.

AUX OFFSET function
(alignment of the portable device volume to the
one of the other sources)

(for versions/markets, where provided)

This function enables to align the volume of the AUX
source, depending on its own portable player, to the one
of the other sources. To activate the function, press the
MENU button and then select “AUX offset”.

Press the buttons

to decrease or increase the

volume value (set from – 6 to + 6).

221-258 PUNTO Abarth GB 1ed 17-07-2012 13:28 Pagina 241

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands