Abarth Punto Owner'S Handbook Manual Download Page 82

Page: 82 / 271

KNOWING

YOUR VEHICLE

SAFETY

STARTING

AND DRIVING

WARNING LIGHTS

AND MESSAGES

IN AN

EMERGENCY

MAINTENANCE

AND CARE

TECHNICAL

SPECIFICATIONS

CONTENTS

fig. 76

EXTENDING THE BOOT

Tilting the rear seat forwards gives maximum loading
volume.

Proceed as follows:

❒

fully lower the rear seat head restraints;

❒

check that the seat belts are not twisted;

fig. 77

fig. 78

❒

tilt the cushions forward as shown by the arrow
fig. 76;

❒

operate the handles A and B-fig. 77 to release the
backrests and guide them down onto the cushion.

069-108 PUNTO Abarth GB 1ed 17-07-2012 12:07 Pagina 78

Summary of Contents for Punto
















































































































































































































































































Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands

Abarth Punto, Owner'S Handbook Manual

Search results

Summary of Contents for Punto

Reviews:

Related manuals for Punto

Brands by name

Popular brands