3Com V6100, User Manual Manual, Page: 322 / 496

322
V6100 and V7122 User Guide
FORMAT SS7_LINK_INDEX = SS7_LINK_NAME, SS7_LINK_TRACE_LEVEL,
SS7_LINK_ADMINISTRATIVE_STATE,SS7_LINK_L2_TYPE, SS7_LINK_L3_TYPE,
SS7_LINK_TRUNK_NUMBER,SS7_LINK_TIMESLOT_NUMBER,SS7_LINK_M2UA_IF_ID;
SS7_LINK_TABLE 0 = new_link_0, 0, 2, 1,1, 1, 15,50;
SS7_LINK_TABLE 1 = new_link_1, 0, 2, 1,1, 2, 12, 12;
SS7_LINK_TABLE 2 = new_link_2, 0, 2, 1, 1, 4, 7,18;
SS7_LINK_TABLE 3 = new_link_3, 0, 2, 1, 1, 5, 3,1;
[\SS7_LINK_TABLE]
[ SS7_SIG_IF_GROUP_TABLE ]
FORMAT SS7_SIG_IF_GR_INDEX = SS7_IF_GR_ID,SS7_SIG_SG_MGC, SS7_SIG_LAYER,
SS7_SIG_TRAF_MODE, SS7_SIG_T_REC, SS7_SIG_T_ACK, SS7_SIG_T_HB, SS7_SIG_MIN_ASP,
SS7_SIG_BEHAVIOUR, SS7_LOCAL_SCTP_PORT, SS7_SIG_NETWORK;
SS7_SIG_IF_GROUP_TABLE 4 = 4,83, 2, 1, 2000, 2000, 30000, 1, 0, 2904, 1;
[ \SS7_SIG_IF_GROUP_TABLE ]
[ SS7_SIG_INT_ID_TABLE ]
FORMAT SS7_SIG_IF_ID_INDEX = SS7_SIG_IF_ID_VALUE, SS7_SIG_IF_ID_NAME,
SS7_SIG_IF_ID_OWNER_GROUP, SS7_SIG_IF_ID_LAYER, SS7_SIG_IF_ID_NAI, SS7_SIG_M3UA_SPC;
SS7_SIG_INT_ID_TABLE 7 = 50, BELFAST12, 4, 2, 0, 0;
SS7_SIG_INT_ID_TABLE 8 = 12, AMSTERDAM, 4, 2, 1, 0;
SS7_SIG_INT_ID_TABLE 9 = 18, ROTERDAM , 4, 2, 2, 0;
SS7_SIG_INT_ID_TABLE 10 = 1, GAUDA , 4, 2, 3, 0;
[ \SS7_SIG_INT_ID_TABLE ]
QSIG Tunneling
The V7122 supports QSIG tunneling over SIP according to <draft-elwell-sipping-qsig-tunnel-
03>. This method enables all QSIG messages to be sent as raw data in corresponding SIP
messages using a dedicated message body. This mechanism is useful for two QSIG
subscribers (connected to the same / different QSIG PBX) to communicate with each other
over an IP network. Tunneling is supported for both directions (Tel to IP and IP to Tel).
The term tunneling means that messages are transferred ‘as is’ to the remote side, without
being converted (QSIG
Æ
SIP
Æ
QSIG). The advantage of tunneling over QSIG
Æ
SIP
interworking is that by using interworking, QSIG functionality can only be partially achieved.
When tunneling is used, all QSIG capabilities are supported, whereas the tunneling medium
(the SIP network) does not need to process these messages.