![background image](http://html1.mh-extra.com/html/3com/v6100/v6100_user-manual-manual_3139483169.webp)
V6100 and V7122 User Guide
169
ini File Field Name
Web Parameter Name
Valid Range and Description
EnableParametersMonitori
ng
Obsolete parameter, use the parameter ‘ActivityListToLog’ instead.
MaxEchoCancellerLength
[Max Echo Canceller
Length]
It isn’t necessary to
configure the parameter
EchoCancellerLength as it
automatically acquires its
value from the parameter
MaxEchoCancellerLength.
Maximum Echo Canceler Length in msec:
0 = Internal decision to keep max channel capacity (currently 32 msec)
4 = 32 msec
11 = 64 msec
22 = 128 msec
The default value is 0.
When set to 128 msec, the number of available gateway channels
is reduced by a factor of 5/6.
For example:
Gateway with 8 E1 spans capacity is reduced to 6 spans (180
channels), while gateway with 8 T1 spans capacity remains the
same (192 channels).
The gateway must be reset after the value of
‘MaxEchoCancellerLength’ is changed.
ECHybridLoss
Sets the four wire to two wire worst case Hybrid loss, the ratio between the
signal level sent to the hybrid and the echo level returning from the hybrid.
0 = 6 dB (default)
1 = 9 dB
2 = 0 dB
3 = 3 dB
GwDebugLevel
[Debug Level]
Defines the Syslog logging level (usually set to 5 if debug traces are
needed).
0 = Debug is disabled (default)
1 = Flow debugging is enabled
2 = Flow and board interface debugging are enabled
3 = Flow, board interface and stack interface debugging are enabled
4 = Flow, board interface, stack interface and session manager debugging
are enabled
5 = Flow, board interface, stack interface, session manager and board
interface expanded debugging are enabled
CDRReportLevel
[CDR Report Level]
0 = CDR is not used
1 = Call Detail Record is sent to the Syslog server at the end of each call.
2 = CDR report is send to Syslog at start and at the end of each call
The CDR Syslog message complies with RFC 3161 and is identified by:
Facility = 17 (local1) and Severity = 6 (Informational)
This parameter replaces the previous ‘EnableCDR’ parameter
CDRSyslogServerIP
[CDR Server IP Address]
Defines the destination IP address for CDR logs.
The default value is a null string that causes the CDR messages to be sent
with all Syslog messages.
The CDR messages are sent to UDP port 514 (default Syslog port).
HeartBeatDestIP
Destination IP address (in dotted format notation) to which the gateway
sends proprietary UDP ‘ping’ packets.
The default IP address is 0.0.0.0.
Summary of Contents for V6100
