![background image](http://html1.mh-extra.com/html/3com/v6100/v6100_user-manual-manual_3139483267.webp)
V6100 and V7122 User Guide
267
RTP NO-OP
This feature complies with the IETF’s draft-wing-avt-rtp-noop-03.txt titled ‘A No-Op Payload
Format for RTP’.
The IETF document defines a no-op payload format for RTP. This can be used to verify RTP
connectivity and to keep NAT bindings and Firewall pinholes open. The draft defines the
RTP payload as dynamic. 3Com’ default payload type is 120.
Users can control activation of the RTP No-Op Packets by setting the parameter
RTPNoOpEnable.
Receipt of No-Op is always supported.
If RTP No-Op packet transmission is activated, users can control the time interval in
which the No_Op packets are sent in the case of silence (no RTP traffic). This is
performed using parameter RTPNoOpInterval.
Users can control the payload type with which the No_Op packets are sent. This is
performed using parameter RTPNoOpPayloadType
.
Point-to-Point Protocol over Ethernet (PPPoE)
PPPoE is a method of sending the Point-to-Point Protocol over Ethernet network.
Point-to-Point Protocol (PPP) Overview
Point-to-Point Protocol (PPP) provides a method of transmitting data over serial point-to-
point links. The protocol defines establishing, configuring and testing the data link connection
and the network protocol.
The PPP standard describes a state machine used to establish a valid connection between
two hosts over a serial connection. There are three major stages described, helping to
establish a network layer (such as an IP) connection over the point-to-point link: LCP (Link
Configuration Protocol) Authentication and NCP (Network Control Protocol). Once the
network protocol is configured, the two hosts can communicate, sending network layer
protocol (such as IP) over the PPP connection (a small PPP header is added at the
beginning of each packet).
At the initial phase, the hosts use LCP (link configuration protocol) to negotiate for link
characteristic and parameters. Packets sent in this phase have two octets of ‘PPP header’
followed by LCP message with variable length. Various parameters and options are
negotiable at this phase, including MRU (maximum receive unit), Authentication Protocol,
and others.
Summary of Contents for V6100
