V6100 and V7122 User Guide
209
ini File Field Name
Web Parameter Name
Valid Range and Description
ConnectOnProgressInd
0 = Connect message isn’t sent after 183 Session Progress is received
(default).
1 = Connect message is sent after 183 Session Progress is received.
This feature enables the play of announcements from IP to PSTN without the
need to answer the Tel
Æ
IP call. It can be used with PSTN networks that don’t
support the opening of a TDM channel before an ISDN Connect message is
received.
SIP183Behaviour
[183 Message Behavior]
Defines the ISDN message that is sent when 183 Session Progress message
is received for IP
Æ
Tel calls.
0 = Progress message (default).
1 = Alert message.
When set to 1, the gateway sends an Alert message (after the receipt of a 183
response) instead of an ISDN Progress message.
LocalISDNRBSource_ID
[Local ISDN Ringback
Tone Source]
ID = Trunk number (0-7).
Determines whether Ringback tone is played to the ISDN by the PBX / PSTN
or by the gateway.
0 = PBX / PSTN (default).
1 = Gateway.
This parameter is applicable to ISDN protocols. It is used simultaneously with
the parameter ’PlayRBTone2Trunk’.
LocalISDNRBSource
[Local ISDN Ringback
Tone Source]
Obsolete parameter, use LocalISDNRBSource_ID instead.
PSTNAlertTimeout
[PSTN Alert Timeout]
Alert Timeout in seconds (ISDN T301 timer) for outgoing calls to PSTN.
The default is 180 seconds. The range is 0 to 240.
The PSTN stack T301 timer can be overridden by a lower value,
but it can’t be increased.
EnableTransferCap
[Enable Transfer
Capability]
N/A.
Must be set to 0 (disable).
ISDNTransferCapability_
ID
[ISDN Transfer
Capabilities]
ID = Trunk number (0-7).
Defines the IP
Æ
ISDN Transfer Capability of the Bearer Capability IE in ISDN
Setup messages.
0 = Audio 3.1 (default).
1 = Speech.
2 = Data.
If this parameter isn’t configured or equals to ‘–1’, Audio 3.1
capability is used.
ISDNTransferCapability
[ISDN Transfer
Capabilities]
Obsolete parameter, use ISDNTransferCapability_ID instead.
SendISDNTransferOnCo
nnect
[ISDN Transfer On
Connect]
0 = Enable ISDN Transfer if outgoing call is in Alert state (default).
1 = Enable ISDN Transfer only if outgoing call is in Connect state.
This parameter is used for the ECT/TBCT/RLT ISDN Transfer methods.
Usually, the gateway requests the PBX to connect an incoming and an
outgoing call. This parameter determines if the outgoing call (from the gateway
to the PBX) must be connected before the transfer is initiated.
Summary of Contents for V6100
