Zte ZXR10 GER Скачать руководство пользователя страница 344

Страница: 344 / 412

ZXR10 GER (V2.6.03) General Excellent Router User Manual Volume-I

322

Confidential and Proprietary Information of ZTE CORPORATION

2. To set interface for support RSVP signaling, use

mpls

traffic-eng tunnels

in interface configuration mode as

shown in Table 367.

A B L E

3 6 7

P L S

R A F F I C

N T E R F A C E

O M M A N D

Command

Format

Command

Mode

Command Function

mpls

traffic-
eng
tunnels

Interface config This enables MPLS TE on an

interface

Result:

This configures MPLS TE signaling on an

interface.

Note:

RSVP

is supported on GER Ethernet and Pos

interfaces.

3. To configure the maximum available bandwidth of traffic

engineering and LSP of an interface, use

ip rsvp bandwidth

<max-bandwidth> [<flow-bandwidth>] in interface
configuration mode as shown in Table 368.

A B L E

3 6 8

- R

S V P

O M M A N D

Command

Format

Command

Mode

Command Function

ip rsvp

bandwidth

<max-

bandwidth>
[<flow-

bandwidth>]

Interface config

This sets the parameter for

maximum available bandwidth

Result:

This configures the available bandwidth for traffic

engineering of an interface.

4. To configure the IGP to support TE, following commands are

used:
i. To define the Router of the TE, use

mpls traffic-eng

router-id

<interface-name> command in OSPF

configuration as shown in Table 369.

ii. To configure TE-enabled areas, use

mpls traffic-eng

area

<area-id> command in OSPF config mode as shown

in Table 369.

iii. To enable opaque feature of the OSPF, use command

capability opaque

in OSPF config mode as shown in

Table 369.

Содержание ZXR10 GER





























































































































































































































































































































































































































Результаты поиска

Содержание ZXR10 GER

Отзывы:

Похожие инструкции для ZXR10 GER

Бренды по названию

Популярные бренды

Zte ZXR10 GER, Руководство пользователя

Результаты поиска

Содержание ZXR10 GER

Отзывы:

Похожие инструкции для ZXR10 GER

Бренды по названию

Популярные бренды