Zte ZXMW NR8250 Скачать руководство пользователя страница 63

Страница: 63 / 124

Chapter 2 Alarm

2.2.30 134239931 Transmission unit invalid

Alarm Property

Alarm Code: 134239931

Alarm Information: The transmission unit fails due to alarms 134239928, 134239929,

and 134239930 (1+1 protection and 1+0 protection are distinguished through

subcode)

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 0: Trangsmission unit failure (1+1) caused by the RMU alarm (IF loss of

lock; modulation part is not working properly,baseband part is not working properly);

Sub-code 1: Transmission unit failure (1+0) caused by the RMU alarm (IF loss of lock;

modulation part is not working properly; baseband part is not working properly);

Sub-code 2: Transmission unit failure (1+1) caused by the ODU alarm (Tx RF PLL

loss of lock;Tx IF PLL loss of lock; Rx RF PLL loss of lock; Rx IF PLL loss of lock);

Sub-code 3: Transmission unit failure (1+0) caused by the ODU alarm (Tx RF PLL

loss of lock; Tx IF PLL loss of lock; Rx RF PLL loss of lock; Rx IF PLL loss of lock).

Effect on the System

The traffic carried by the transmission unit is interrupted.

Possible Causes

Refer to the probable causes of the alarms 134239928, 134239929, and 134239930.

Handling Procedure

Refer to the handling suggestions of the alarms 134239928, 134239929, and 134239930.

2.2.31 134239935 ODU mute

Alarm Property

Alarm Code: 134239935

Alarm Information: The alarm is reported if the transmission power of ODU is set to 0

in LMT.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

2-49

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды