Zte ZXMW NR8250 Скачать руководство пользователя страница 60

Страница: 60 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: The modulation and demodulation part is unlocked;

Sub-code 2: The CPU running is suspended in modulation and demodulation;

Sub-code 3: The protection function initialization for the RMU board fails.

Effect on the System

For subcode 1:

In non-protection mode, the traffic is interrupted.

In protection mode, if both the active and standby traffic units are unlocked, the

traffic is interrupted; otherwise, the active/standby changeover is performed.

For subcode 2:

In non-protection mode, the traffic is interrupted.

In protection mode, if both the active and standby traffic units are suspended, the

traffic is interrupted; otherwise, the active/standby changeover is performed, and

the service is not affected.

For subcode 3:

The receive-end protection function that RMU is configured with does not take effect,

thus the protection cannot be implemented.

Possible Causes

The configurations at both ends are incorrect.

The local transceiver and the remote transceiver are faulty.

The NR8250 shelf at the local end is faulty.

Handling Procedure

Check whether the configurations at the two ends including ODU frequency,

modulation modes, and bandwidth are consistent.

If yes, go to step 2.

If no, it indicates that the configuration is incorrect. Issue the data again.

Check whether the local end reports the unlock alarm (alarm code: 134239928).

If yes, replace the RMU board at the local end.

If no, go to step 3.

Check whether the remote end reports the unlock alarm (alarm code: 134239928). If

yes, replace the RMU board.

When the alarm of sub-code 3 is reported, cold start the active and standby RMU

boards. If the alarm persists, go to step 5.

Replace the active and slave RMU boards that report the alarm. If the alarm persists,

replace the N8250 shelf at the local end.

2-46

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды