Zte ZXMW NR8250 Скачать руководство пользователя страница 52

Страница: 52 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code Description

Each subcode represents a timeslot. The former 63 timeslots are used for optical port 1,

and the latter 63 timeslots are used for optical port 2.

Effect on the System

The signal transmitted on the SDH link is interrupted.

Possible Causes

The actual J2 value is inconsistent with the preset j2 value.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Contact the network engineer.

2.2.19 134237753 HP-PLM

Alarm Property

Alarm Code: 134237753

Alarm Information: The alarm is reported if higher order path signal flag is mismatched.

This is detected by C2.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: STM-1 of optical port 1 (LMT displays "STM-1");

Sub-code 5: Path 1 of optical port 2 (LMT displays "STM-4-Channel1");

Sub-code 6: Path 2 of optical port 2 (LMT displays "STM-4-Channel2");

Sub-code 7: Path 3 of optical port 2 (LMT displays "STM-4-Channel3");

Sub-code 8: Path 4 of optical port 2 (LMT displays "STM-4-Channel4");

Sub-code 10: STM-1 of optical port 2 (LMT displays "2STM-1").

Effect on the System

All the relay receive signals transmitted on the SDH link may be interrupted.

Possible Causes

The signal flag received by NR8250 equipment is inconsistent with that sent by the

upstream equipment.

The RTUB board that reports the alarm is faulty.

2-38

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды