Zte ZXMW NR8250 Скачать руководство пользователя страница 113

Страница: 113 / 124

Chapter 3 Notification

Effect on the System

The neighbor status is changed, and the route may be recalculated.

Possible Causes

The OSPF interface is disabled by administrator in EMS or LMT.

Handling Procedure

Check whether the interface configuration is enabled.

3.27 134243747 OSPF interface disabled physically

Notification Property

Notification Code: 134243747

Notification Information: The alarm is reported if OSPF interface is disabled due to

physical reasons such as network media.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

The neighbor status is changed, and the route may be recalculated.

Possible Causes

The network media is disconnected.

Handling Procedure

Check the pyhsical connections.

3.28 134243748 interface's neighbor changed

Alarm Property

Alarm Code: 134243748

Alarm Information: OSPF interface's neighbor configuration is changed

Alarm Level: Major

Alarm Type: Handling Alarm

Alarm Sort: Notification

3-17

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды