Zte ZXMW NR8250 Скачать руководство пользователя страница 66

Страница: 66 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

If no, go to step 3.

Select

ETH > OAM_CFM > Operation Result Info

and

ETH > OAM_EFM > Protocol

Info

to check whether the network is congested. If yes, contact the network engineer.

2.2.34 134243752 RMEP CCM packet error

Alarm Property

Alarm Code: 134243752

Alarm Information: The alarm is reported if LMEP receives incorrect CCM packet.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board. The purpose is to inform the administrator

that the basic CFM configuration has errors.

Possible Causes

RMEP is faulty or RMEP configuration is incorrect.

Handling Procedure

Check whether each RMEP configuration (IP address, MAC address, an CCM packet

sending period of MD/MA/LMEP and LMEP) corresponding to the LMEP in the alarm is

consistent with the LMEP configuration of corresponding MA at the remote end. If no,

modify the configurations to be consistent.

2.2.35 134243753 RMEP port status abnormal

Alarm Property

Alarm Code: 134243753

Alarm Information: The alarm is reported if LMEP receives the CCM packet in which

the RMEP port status information is abnormal.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

2-52

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды