Zte ZXMW NR8250 Скачать руководство пользователя страница 53

Страница: 53 / 124

Chapter 2 Alarm

Handling Procedure

Check whether the flag of C2 signal sent from NR8250 upstream equipment is correct,

which is 0X12 for VC4 and 0x02 for VC12.

If yes, go to step 2.

If no, modify the configuration.

The alarm is caused by RTUB board failure. Replace the board.

2.2.20 134237754 TU-PLM

Alarm Property

Alarm Code: 134237754

Alarm Information: The alarm is reported if tributary unit signal flag is mismatched.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Each subcode represents a timeslot. The former 63 timeslots are used for optical port

1,and the latter 63 timeslots are used for optical port 2.

Effect on the System

All the relay receive signals transmitted on the SDH link may be interrupted.

Possible Causes

The signal flag received by NR8250 equipment is inconsistent with that sent by the

upstream equipment.

The RTUB board that reports the alarm is faulty.

Handling Procedure

Contact the network engineer.

2.2.21 134237756 TU-LOP

Alarm Property

Alarm Code: 134237756

Alarm Information: The alarm is reported if tributary unit pointer is lost.

Alarm Level: Major

Alarm Type: Communications Alarm

2-39

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды