Zte ZXMW NR8250 Скачать руководство пользователя страница 16

Страница: 16 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

RCU 0X30XX

RTU 0X91XX

RMU 0X92XX

PM 0X37XX

Turn on the board's power supply.

2.1.2 1002 Board not in position

Alarm Property

Alarm Code: 1002

Alarm Information: This alarm is reported when the board is configured in the network

management system but is not inserted in the actual slot.

Alarm Level: Critical

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The board cannot bear any service.

Possible Causes

The board is configured in a slot on the Local Maintenance Terminal (

LMT

) but not

actually inserted in that slot.

The board is configured in a slot on the LMT but not tightly inserted in that slot.

The board is configured in a slot on the LMT but the connecting part is physically

damaged.

Handling Procedure

Check whether the board is inserted into the slot.

If yes, go to step 2.

If no, insert the board.

Pull out and plug the board into the slot. If the alarm persists, go to step 3.

Replace the shelf.

2.1.3 1004 Board not configured

Alarm Property

Alarm Code: 1004

Alarm Information: This alarm is reported when the board is configured in the network

management system but is not inserted in the actual slot.

2-2

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды