Zte ZXMW NR8250 Скачать руководство пользователя страница 40

Страница: 40 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

2.2.3 134217737 UAS alarm of MS

Alarm Property

Alarm Code: 134217737

Alarm Information: This alarm is reported when UAS change at MS is detected.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Optical port 1 on the RTUB board;

Sub-code 2: Optical port 2 on the RTUB board.

Effect on the System

This alarm affects traffic.

Possible Causes

The uplink optical port service degrades and causes the UAS to occur.

Handling Procedure

Check whether the receive power and transmit power of the optical module are normal.

If yes, go to step 2.

If no, replace the optical module and ensure that the uplink equipment operates

properly.

Replace the RTUB.

2.2.4 134217738 UAS alarm of RS

Alarm Property

Alarm Code: 134217738

Alarm Information: This alarm is reported when UAS change at RS is detected.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Optical port 1 on the RTUB board;

Sub-code 2: Optical port 2 on the RTUB board.

Effect on the System

This alarm affects traffic.

2-26

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды