Zte ZXMW NR8250 Скачать руководство пользователя страница 109

Страница: 109 / 124

Chapter 3 Notification

Possible Causes

The status of an OSPF virtual interface neighbor is changed. All OSPF interface neighbor

status packets include: Down, Init, 2Way, ExStart, Exchange, Load, and Full.

Handling Procedure

No processing is required.

3.20 134243740 OSPF interface receiving incorrect

packet

Notification Property

Notification Code: 134243740

Notification Information: The alarm is reported if OSPF interface receives incorrect

packet, which cannot be parsed.

Notification Type: Handling Alarm

Sub-code Description

None

Effect on the System

This alarm may cause LSDB synchronization failure.

Possible Causes

The contents of the DD, LSR, LSAck, and LSU packets are incorrect.

Handling Procedure

No processing is required.

3.21 134243741 OSPF virtual link interface receiving

incorrect packet

Notification Property

Notification Code: 134243741

Notification Information: The alarm is reported if OSPF virtual interface receives

incorrect packet, which cannot be parsed.

Notification Type: Handling Alarm

3-13

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды