Zte ZXMW NR8250 Скачать руководство пользователя страница 59

Страница: 59 / 124

Chapter 2 Alarm

Alarm Information: The alarm is reported if the IF is unlocked due to abnormal external

clock of the IF unit or internal hardware fault.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

In non-protection mode, traffic is interrupted.

In protection mode:

Traffic is interrupted if both active and standby RMUs are unlocked.

Switchover is performed if the active RMU is unlocked.

Possible Causes

The IF is unlocked.

The IF circuit is faulty.

Handling Procedure

For short-time unlocking:

Detect the alarm and check whether the device is operating normally.

Use the software management software or level recorder to check whether the

fault is caused by attenuation. Check the ODU receiving level.

Check if interference exists. If yes, find out the frequency of the interference

source and change the device frequency.

Adjust the antenna height.

For long-time unlocking:

Check whether the ODU frequencies at both ends match each other.

Check whether the configurations of bandwidth and modulation mode are

consistent at both ends.

Check whether the IF output interface of the ODU unit has rated DC voltage. If

yes, it indicates that the IDU is operating normally. If no, replace the IDU.

Check whether the feeder and feeder connector are in good condition.

Check whether the antenna and ODU installation polarization are correct.

Check whether the antenna azimuth deviates from the designed value.

Check whether the link is blocked.

2.2.28 134239929 Baseband alarm

Alarm Property

Alarm Code: 134239929

Alarm Information: It is the alarm detected in the Modem.

2-45

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды