Zte ZXMW NR8250 Скачать руководство пользователя страница 120

Страница: 120 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Possible Causes

If the ACM mode is disabled, the alarm is caused by user configuration modification. If the

ACM mode is enabled, the alarm is caused by link status change. Users can enable the

ACM mode by selecting

Radio Link > Basic Configuration

Handling Procedure

The notification is reported when the ACM mode is changed due to configuration

modification or link status change. It is not a fault.

3.38 134317746 System time is modified

Notification Property

Notification Code: 134317746

Notification Information: The notification is reported when the system time is modified

due to SNTP-based time calibration.

Notification Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The traffic carried by the board is not affected, but the performance data may become

incomplete.

Possible Causes

The system time is modified .

Handling Procedure

Ensure that the SNTP server time is accurate.

3.39 134317747 Clear performance data

Notification Property

Notification Code: 134317747

Notification Information: This notification is reported when the system clears the

performance data of specified granularity (15 minutes or 24 hours) of a performance

index.

Notification Type: Equipment Alarm

3-24

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды