Zte ZXMW NR8250 Скачать руководство пользователя страница 36

Страница: 36 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Effect on the System

The lightning protector fails.

Possible Causes

The lightning protector is damaged.

The lightning protector's base is of bad contact.

The lightning protector's detecting cable is disconnected or of bad contact.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

Handling Procedure

The lightning protector is damaged. Replace the lightning protector;

Check whether the lightning protector's air break switch is closed;

Check whether the lightning protector's base is of bad contact;

Check whether the contact of the lightnring unit is faulty.

Check the monitoring unit's connection;

Replace the monitoring unit.

2.1.29 9005 AC Under-Volt

Alarm Property

Alarm Code: 9005

Alarm Information: The AC input phase voltage is lower than Phase.OverVolt.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The load capacity of the power supply is influenced, which also affects the normal power

supply for the base station.

Possible Causes

The AC input voltage is low.

The AC under-voltage value of the monitoring unit is set too high.

The AC transducer's connection is faulty or the transducer is damaged.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

2-22

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды