Zte ZXMW NR8250 Скачать руководство пользователя страница 68

Страница: 68 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

The MA names on the two ends are different.

The network has circle or cross connection.

Handling Procedure

Check whether the MA names at the two ends are the same.

If yes, go to step 2.

If no, modify the MA names to be consistent.

Check whether there is no cross connection on the service link. If yes, correct it.

2.2.38 134243756 Frame loss rate exceeding the threshold

Alarm Property

Alarm Code: 134243756

Alarm Information: The alarm is reported if the proportion between the number of lost

data packets and the number of sent data packets exceeds the threshold.

Alarm Level: Major

Alarm Type: Communications Alarm

Sub-code Description

None

Effect on the System

It does not affect the traffic carried by the board.

Possible Causes

Error codes exist in the network or the network bandwidth is insufficient.

Handling Procedure

Check whether the physical layer has any error code, and check the bandwidth usage.

2-54

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды