Zte ZXMW NR8250 Скачать руководство пользователя страница 92

Страница: 92 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Alarm Level: Minor

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The power to the overcurrent board is turned off and the services carried by this board are

completely interrupted.

Possible Causes

The MP current status of the PM board's load is checked periodically. If over-current is

detected, this alarm is reported.

Handling Procedure

Remove and insert the corresponding board;

Replace the corresponding board;

Replace PM board;

Replace the backplane.

2.4.17 405 PP overcurrented

Alarm Property

Alarm Code: 405

Alarm Information: This alarm is reported when the PP current is out of range and

cleared when the current becomes normal.

Alarm Level: Minor

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The power to the over-current board is turned off and the services provided by this board

are interrupted.

Possible Causes

The PP current status of the PM board's load is checked periodically. If over-current is

detected, this alarm is reported.

2-78

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды