Zte ZXMW NR8250 Скачать руководство пользователя страница 17

Страница: 17 / 124

Chapter 2 Alarm

Alarm Level: Critical

Alarm Type: Equipment Alarm

Sub-code Description

Slot ID

Effect on the System

There is no effect on services.

Possible Causes

A board not configured on the LMT is inserted in a slot.

The PM software is faulty and detects board signal from a slot without board.

Handling Procedure

Check whether the board is inserted into the slot.

If yes, go to step 2.

If no, replace the PM board.

Verify that the board needs to be configured.

If yes, configure the board through LMT.

If no, pull out the board.

2.1.4 134217728 Clock reference source lost

Alarm Property

Alarm Code: 134217728

Alarm Information: The alarm is reported if the RCU cannot detect the clock signal of

configured clock reference source.

Alarm Level: Minor

Alarm Type: Equipment Alarm

Sub-code Description

Sub-code 1: RCU 1PPS+TOD clock lost;

Sub-code 2: RCU BITS clock lost;

Sub-code 4: Slot3 clock lost;

Sub-code 5: Slot4 clock lost;

Sub-code 6: Slot5 clock lost;

Sub-code 7: Slot6 clock lost;

Sub-code 8: Slot7 clock lost;

Sub-code 9: Slot8 clock lost;

Sub-code 10: RCU NMS clock lost;

Sub-code 11: RCU GbE clock lost;

Sub-code 12: 1588 clock lost.

2-3

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды