Zte ZXMW NR8250 Скачать руководство пользователя страница 44

Страница: 44 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Handling Procedure

Check whether the optical fiber is in good condition, and the optical connector is clean

and connected properly.

If yes, replace the optical fiber. Clean the optical connector and install it again.

If no, replace the RTUB board.

Ensure that the signal source of upstream equipment and the connected NR8250

equipment use the same clock source.

Replace the optical module and ensure that the optical module type and rate are the

same as those configured in the LMT system.

2.2.8 134237736 RS-OOF

Alarm Property

Alarm Code: 134237736

Alarm Information: The alarm indicates that interruption occurs at the regenerator

section. The local end does not receive the signal from the remote end.

Alarm Level: Critical

Alarm Type: Communications Alarm

Sub-code Description

Sub-code 1: Optical port 1 on the RTUB board;

Sub-code 2: Optical port 2 on the RTUB board.

Effect on the System

The board cannot identify the data frame for the received SDH signal, and the service is

interrupted.

Possible Causes

The clock configuration is different from that of the upstream device.

Too many error codes are generated during the transmission.

The RTU board that reports the alarm is faulty.

Handling Procedure

Check whether the upstream device signal source uses the same clock source as the

connected NR8250 device.

If yes, go to step 2.

If no, modify the configuration to ensure that use the same clock source is used.

Replace the RTUB board.

2-30

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды