Zte ZXMW NR8250 Скачать руководство пользователя страница 106

Страница: 106 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Sub-code 2: The RPL OWNER port is blocked due to being controlled by the 8032

protocol.

Effect on the System

This alarm may cause traffic transmission path switchover and service interruption.

Possible Causes

The local link is interrupted.

The 8032 single-ring network is initialized.

The ring network link changes from the standby to the active.

Handling Procedure

If the alarm sub-code is 1, check the east-port and west-port link of the equipment that

reports the alarm.

3.15 134243732 8032 port unblocked

Alarm Property

Alarm Code: 134243732

Alarm Information: The notification is reported if the 8032 protocol sends a unblock

request to the switching chip and the chip is unblocked.

Alarm Type: Equipment Alarm

Sub-code Description

Sub-code 1: The port is unblocked due to local link recovery;

Sub-code 2: The RPL OWNER port is unblocked due to the SF packet being received.

Effect on the System

This alarm may cause traffic transmission path switchover and service interruption.

Possible Causes

The local link is restored.

The ring network link switches from the active to the standby.

Handling Procedure

No processing is required.

3-10

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды