Zte ZXMW NR8250 Скачать руководство пользователя страница 34

Страница: 34 / 124

ZXMW NR8250 Alarm and Notification Handling Reference

Possible Causes

The air break switch of the main AC input is not closed.

The main air break switch's contact is disconnected or of bad contact.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

The AC loop is short-circuited.

Handling Procedure

If the air break switch of the main AC input is not closed, then close it;

Check the air break switch's contact;

Check whether the monitoring unit's socket is inserted properly;

Replace the monitoring unit.

2.1.26 9002 AC Power Off

Alarm Property

Alarm Code: 9002

Alarm Information: The mains supply is cut off and there is no standby AC input.

Alarm Level: Critical

Alarm Type: Equipment Alarm

Sub-code Description

None

Effect on the System

The rectifier fails to work normally, only the battery can work.

The system does not implement battery management.

When the battery runs out, the base station is powered down.

Possible Causes

The AC power supply is powered down.

The AC transducer's connection is faulty or the transducer is damaged.

The monitoring unit's socket is of bad contact or disconnected.

The monitoring unit is faulty.

Handling Procedure

If the AC power supply is powered down, use the generator to provide power supply.

Check whether the AC transducer's connection is normal and whether the transducer

has no problem.

Check whether the monitoring unit's socket is inserted properly.

Replace the monitoring unit.

2-20

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Содержание ZXMW NR8250





























































































































Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды

Zte ZXMW NR8250, Руководство пользователя

Результаты поиска

Содержание ZXMW NR8250

Отзывы:

Похожие инструкции для ZXMW NR8250

Бренды по названию

Популярные бренды