YOKOGAWA TA720 Скачать руководство пользователя страница 48

Страница: 48 / 228

3-1

IM 704510-01E

Before Starting Measurements

Chapter 3 Before Starting Measurements

3.1

Handling Precautions

Safety Precautions

• When using the TA720 for the first time, make sure to read the “Safety Precautions”

given on pages iv and v.

• Do not remove the cover from the instrument. Some sections inside the instrument have

high voltages that are extremely dangerous. For internal inspection or adjustment,

contact your nearest YOKOGAWA dealer as listed on the back cover of this manual.

• Never continue to use the instrument if there are any symptoms of trouble such as strange

odors or smoke coming from the instrument. In such cases, immediately turn OFF the power

and unplug the power cord. If such an irregularity occurs, contact your dealer or the nearest

YOKOGAWA representative, as listed on the back cover of this manual.

• If the following error message is displayed, immediately turn OFF the power. The

cooling fan has stopped. From the rear panel, check for and remove any foreign

object that may be obstructing the cooling fan. If the same error message appears

when you turn ON the power switch again, it is probably a malfunction. In this case,

contact your nearest YOKOGAWA dealer.

• Nothing should be placed on top of the power cord. The power cord should also be

kept away from any heat sources. When unplugging the power cord from the outlet,

never pull by the cord itself. Always hold and pull by the plug. If the power cord is

damaged, contact your dealer for replacement. Refer to page ii for the part number of

the appropriate power cord when placing an order.

General Handling Precautions

• Never place any objects containing water on top of the instrument. Such act can lead

to malfunction.

• Do not apply shock or vibration. Such act can lead to malfunction. Take extra caution

because the built-in floppy disk drive is sensitive to vibration and shock. In addition,

applying shock to the input/output terminal or the connected cable can cause

electrical noise to enter or output from the instrument.

• Do not bring charged objects near the input/output terminals. Such act can lead to

malfunction.

• If you are not going to use the instrument for a long period of time, unplug the power

cord from the outlet.

• When carrying the instrument, unplug the power cord and cables. The instrument

weighs approximately 12 kg. To carry the instrument, use the handle as shown in the

figure below, and move it with care.

Содержание TA720





































































































































































































































Результаты поиска

Содержание TA720

Отзывы:

Похожие инструкции для TA720

Бренды по названию

Популярные бренды

YOKOGAWA TA720, Руководство пользователя

Результаты поиска

Содержание TA720

Отзывы:

Похожие инструкции для TA720

Бренды по названию

Популярные бренды