Yamatake HGC303 Скачать руководство пользователя страница 9

Страница: 9 / 130

Yamatake Corporation

Safety

Model HGC303 - Heat Value Gas Chromatograph

vii

4. Class II, Division 2 locations

4.1

Wiring methods

•

Rigid metal conduit, intermediate metal conduit, electrical metallic tubing,
dust-tight wireways, or Type MC or MI cable with approved termination
fittings

, or

Type PLTC in cable trays

, or

Type ITC in cable trays

, or

Type

TC cable installed in ladder, ventilated trough, or ventilated channel

cable trays in a single layer, with a space not less than the larger cable
diameter between the two adjacent cables

, can be employed.

• All boxes and fittings must be dusttight.

4.2

Sealing

• Sealing means must be provided as shown in 3.2.

5. Class III, Division 1 locations

5.1

Wiring methods

•

Rigid metal conduit, rigid non-metallic conduit, intermediate metal conduit,
electrical metallic tubing, dust-tight wireways

, or

Type MC or MI cable with

approved termination fittings

, can be employed.

• All boxes and fittings must be dusttight.

5.2

Sealing

• Sealing means are not required.

6. Class III, Division 2 locations

6.1

Wiring methods

• Wiring methods must comply with 5.1.

6.2

Sealing

• Sealing means are not required.

Содержание HGC303



































































































































Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды

Yamatake HGC303, Руководство пользователя

Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды