Yamatake HGC303 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 130

background image

Yamatake Corporation

Safety

Model HGC303 - Heat Value Gas Chromatograph

iii

(1) Installation for ISSeP/ATEX Flameproof Apparatus

1. General

1.1

The apparatus protected by the flameproof enclosure

in accordance with EN

50018 can be installed in such hazardous areas, for which the apparatus has been
certified, as an explosive atmosphere containing flammable substances in the form
of

gas

,

vapour

,

mist

or

dust

may be present.

~Note

The apparatus has been certified to comply with EN 50281-1-1 (dust

ignition protection).

1.2

The apparatus enclosure must be kept closed in the hazardous areas when the
apparatus is energized

because the internal circuit of the apparatus is capable of

igniting the explosive atmosphere. (Never connect any hand-held communicator to
the apparatus terminals by opening the cover, except while no explosive
atmosphere is present.)

1.3 It is required to connect

the external earthing terminal of the apparatus to the

equipotential bonding system

which includes protective conductors, metal

conduits, metal cable sheaths, steel wire armouring and metallic parts of structures,
but does not include the neutral conductors of the power systems.

~Note

The protective conductor to which exposed conductive parts of equipment

(machines, apparatus, devices, components and instrumentation thereof)

are connected, must be separated in the hazardous area from the neutral

conductor, and must be connected to the power systems earth point in the

non-hazardous area, if the power system is directly earthed.

For external earthing and bonding of the apparatus it is recommended to use a
cable lug so that the conductor is secured against loosening and twisting and that
the contact pressure is permanently secured.

1.4 Either

cable systems

(cable entry systems) or

conduit systems

can be employed

for wiring of the apparatus in the hazardous areas (see 2 or 3).

1.5

Non-sheathed single core cables are not permitted for live conductors

unless

they are installed inside enclosures or conduit systems.

1.6

Conduits

and,

in special cases

,

cables

(for example, where there is a pressure

difference)

must be sealed

so as to prevent the passage of the explosive

atmosphere.

1.7

Further information concerning installation and maintenance of apparatus

is

given by relevant clauses of the following documents.

EN 60079-14 Electrical apparatus for explosive gas atmospheres

Part 14:

Electrical installations in hazardous areas other than mines

EN 60079-17

Part 17:

Inspection and maintenance of electrical installations in

hazardous areas.

EN 50281-1-2 Electrical apparatus for use in the presence of combustible dust

Part 1-2: Electrical apparatus protected by enclosures

-- Selection, installation and maintenance

«
...
3
4
5
6
7
...
»

Содержание HGC303



































































































































Отзывы:

Нет отзывов

Похожие инструкции для HGC303

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: Unex Страницы: 5

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

FlexDraper FD2 Series

Бренд: MacDon Страницы: 2

OXYGEN PRO MINI

Бренд: M-Audio Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды