Yamatake HGC303 Скачать руководство пользователя страница 44

Страница: 44 / 130

Operation

Yamatake Corporation

3-2

Model HGC303 - Heat Value Gas Chromatograph

3-1-3 : Power on

Supply the power to operate the model HGC303 system according to the following
action.

~Note

After turning on the power, allow 2 hours for the device to warm up.

The carrier gas pressure SP and oven temperature SP have already been factory set in
the model HGC303, therefore, the user doesn't have to worry about setting this data.

Carrier gas pressure SP: less than 300 kPa (43.5 psi)
(SP differs with each model HGC303)

Oven temperature SP: 58

C (136.4

Analyzing cycle: 300 sec.

~Note

When the power is supplied to the model HGC303, a model HGC303

status error will appear on HGM monitoring system (oven temperature

error message etc.

This is because of a self-diagnostic system error, not a model HGC303

system error.

The model HGC303 status will automatically return to normal once the

oven temperature reaches 58

C (136.4

F).

Table 3-2 The procedure to start up the model HGC303 system

Step

Action

Supply the valve operating gas

Supply the carrier gas pressure

Supply the power to the model HGC303

Supply the power to the model HMU303

Wait until the model HGC303 system becomes stale.

Supply the process gas

Содержание HGC303



































































































































Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды

Yamatake HGC303, Руководство пользователя

Результаты поиска

Содержание HGC303

Отзывы:

Похожие инструкции для HGC303

Бренды по названию

Популярные бренды